Operating Systems

4.9: Research on Memory Management

Skipped

4.10: Summary

Read

Some Last Words on Memory Management

• Segmentation / Paging / Demand Loading (fetch-on-demand)
  • Each is a yes or no alternative.
  • Gives 8 possibilities.
• Placement and Replacement.
• Internal and External Fragmentation.
• Page Size and locality of reference.
• Multiprogramming level and medium term scheduling.

Chapter 5: Input/Output

5.1: Principles of I/O Hardware

5.1.1: I/O Devices

• Not much to say. Devices are varied.
• Block versus character devices:
  • Devices, such as disks and CDROMs, with addressable chunks (sectors in this case) are called block devices,
    These devices support seeking.
  • Devices, such as Ethernet and modem connections, that are a stream of characters are called character devices.
    These devices do not support seeking.
  • Some cases, like tapes, are not so clear.

5.1.2: Device Controllers

These are the “devices” as far as the OS is concerned. That is, the OS code is written with the controller spec in hand not with the device spec.

• Also called adaptors.
  
  
• The controller abstracts away some of the low level features of the device.
  
  
• For disks, the controller does error checking and buffering.
  
  
• (Unofficial) In the old days it handled interleaving of sectors. (Sectors are interleaved if the controller or CPU cannot handle the data rate and would otherwise have to wait a full revolution. This is not a concern with modern systems since the electronics have increased in speed faster than the devices.)
  
  
• For analog monitors (CRTs) the controller does a great deal. Analog video is very far from a bunch of ones and zeros.
  
  

5.1.3: Memory-Mapped I/O

Think of a disk controller and a read request. The goal is to copy data from the disk to some portion of the central memory. How do we do this?

• The controller contains a microprocessor and memory and is connected to the disk (by a cable).
  
  
• When the controller asks the disk to read a sector, the contents come to the controller via the cable and are stored by the controller in its memory.
  
  
• The question is how does the OS, which is running on another processor, let the controller know that a disk read is desired and how is the data eventually moved from the controller's memory to the general system memory.
  
  
• Typically the interface the OS sees consists of some device registers located on the controller.
  • These are memory locations into which the OS writes information such as sector to access, read vs. write, length, where in system memory to put the data (for a read) or from where to take the data (for a write).
  • There is also typically a device register that acts as a “go button”.
  • There are also devices registers that the OS reads, such as status of the controller, errors found, etc.
  
  
• So now the question is how does the OS read and write the device register
  • With Memory-mapped I/O the device registers appear as normal memory. All that is needed is to know at which address each device regester appears. Then the OS uses normal load and store instructions to write the registers.
  • Some systems instead have a special “I/O space” into which the registers are mapped and require the use of special I/O space instructions to accomplish the load and store.
  • From a conceptual point of view there is no difference between the two models.

5.1.4: Direct Memory Access (DMA)

• With or without DMA, the disk controller pulls the desired data from the disk to its buffer (and pushes data from the buffer to the disk).
  
  
• Without DMA, i.e., with programmed I/O (PIO), the cpu then does loads and stores (or I/O instructions) to copy the data from the buffer to the desired memory location.
  
  
• With a DMA controller, the controller writes the memory without intervention of the CPU.
  
  
• Clearly DMA saves CPU work. But this might not be important if the CPU is limited by the memory or by system buses.
  
  
• Very important is that there is less data movement so the buses are used less and the entire operation takes less time.
  
  
• Since PIO is pure software it is easier to change, which is an advantage.
  
  
• DMA does need a number of bus transfers from the CPU to the controller to specify the DMA. So DMA is most effective for large transfers where the setup is amortized.
  
  
• Why have the buffer? Why not just go from the disk straight to the memory.
  Answer: Speed matching. The disk supplies data at a fixed rate, which might exceed the rate the memory can accept it. In particular the memory might be busy servicing a request from the processor or from another DMA controller.

Homework: 12

5.1.5: Interrupts Revisited

Skipped.

5.2: Principles of I/O Software

As with any large software system, good design and layering is important.

5.2.1: Goals of the I/O Software

Device independence

We want to have most of the OS, unaware of the characteristics of the specific devices attached to the system. Indeed we also want the OS to be largely unaware of the CPU type itself.

Due to this device independence, programs are written to read and write generic devices and then at run time specific devices are assigned. Writing to a disk has differences from writing to a terminal, but Unix cp and DOS copy do not see these differences. Indeed, most of the OS, including the file system code, is unaware of whether the device is a floppy or hard disk.

Homework: 5.9

Uniform naming

Recall that we discussed the value of the name space implemented by file systems. There is no dependence between the name of the file and the device on which it is stored. So a file called IAmStoredOnAHardDisk might well be stored on a floppy disk.

Error handling

1. Detection should be done as close to where the error occurred as possible before more damage is done (fault containment). This is not trivial.
   
   
2. Correction is sometimes easy, for example ECC memory does this automatically (but the OS wants to know about the error so that it can schedule replacement of the faulty chips before unrecoverable double errors occur).

   Other easy cases include successful retries for failed ethernet transmissions. In this example, while logging is appropriate, it is quite reasonable for no action to be taken.
   

3. Error reporting tends to be awful. The trouble is that the error occurs at a low level but by the time it is reported the context is lost. Unix/Linux in particular is horrible in this area.

Creating the illusion of synchronous I/O

• I/O must be asynchronous for good performance. That is the OS cannot simply wait for an I/O to complete. Instead, it proceeds with other activities and responds to the notification when the I/O has finished.
  
  
• Users (mostly) want no part of this. The code sequence

  Read X
  Y <-- X+1
  Print Y
  

  should print a value one greater than that read. But if the assignment is performed before the read completes, the wrong value is assigned.
  
  
• Performance junkies sometimes do want the asynchrony so that they can have another portion of their program executed while the I/O is underway. That is they implement a mini-scheduler in their application code.

Buffering

• Often needed to hold data for examination prior to sending it to its desired destination.
  
  
• But this involves copying and takes time.
  
  
• Modern systems try to avoid as much buffering as possible. This is especially noticeable in network transmissions, where the data could conceivably be copied many times.
  1. User space --> kernel space as part of the write system call
  2. kernel space to kernel I/O buffer.
  3. I/O buffer to buffer on the network adapter/controller.
  4. From adapter on the source to adapter on the destination.
  5. From adapter to I/O buffer.
  6. From I/O buffer to kernel space.
  7. From kernel space to user space as part of the read system call.
  
  
• I don't know if any systems actually do all seven.

Sharable vs dedicated devices

For devices like printers and tape drives, only one user at a time is permitted. These are called serially reusable devices, and were studied in the deadlocks chapter. Devices like disks and Ethernet ports can be shared by processes running concurrently.